Plastic materials testing · Data-driven quality+86 152 3147 6158
WANSU / HEATED SPECIMEN PRESS

Heated specimen press

Presses plastic granules into specimen sheets by heating, melting and manual pressing, providing specimen preparation for laboratory material testing.

Platen heatingPressure mouldingSpecimen sheet preparation
Model selection1 model documents
Product seriesSample preparation
Sales support +86 152 3147 6158 ↗

Overview

Presses plastic granules into specimen sheets by heating, melting and manual pressing, providing specimen preparation for laboratory material testing.

Applications

01Plastic granules
02Plastic specimen sheets
03Laboratory specimen preparation

Models & specifications

Select a model to view its source specifications in Chinese. Confirm options and delivery configuration when requesting a quote.

MODEL / 01

WS-1002平板硫化仪

Download model document ↗

Introduction & applications

WS-1002型平板硫化机主要用于各种塑料颗粒制样板。温控系统采用WMK-08型温度控制器,具有控温灵敏度高,工作稳定等优点。本机结构精密,控温灵敏、准确,操作方便、适合工厂和科研单位使用。

Technical specifications

WS-1002平板硫化仪

恒温温度室温~350℃
恒温度波动度±0.5℃
温度均匀度±2.5%
加热功率3500W
电源AC220V-15%~AC220V+10% 50Hz (单相三线制)
仪器尺寸加热主机:长810mm×宽350mm×高500mm;
制样机:长300mm×宽220mm×高410mm。
环境条件温度:0~40℃,相对湿度不大于85﹪

Features

平板硫化仪最高温度350℃,可供各种试品置入使用。

本设备的工作温度可由室温升至最高温度,在此范围内,可根据工作需要任意选定工作温度,选定后靠箱内自动控制系统使温度恒定在所规定的范围内。

Read the complete product document

产品资料

WS-1002平板硫化仪

仪器概述

WS-1002型平板硫化机主要用于各种塑料颗粒制样板。温控系统采用WMK-08型温度控制器,具有控温灵敏度高,工作稳定等优点。本机结构精密,控温灵敏、准确,操作方便、适合工厂和科研单位使用。

技术参数

WS-1002平板硫化仪

恒温温度室温~350℃
恒温度波动度±0.5℃
温度均匀度±2.5%
加热功率3500W
电源AC220V-15%~AC220V+10% 50Hz (单相三线制)
仪器尺寸加热主机:长810mm×宽350mm×高500mm;
制样机:长300mm×宽220mm×高410mm。
环境条件温度:0~40℃,相对湿度不大于85﹪

功能特点

平板硫化仪最高温度350℃,可供各种试品置入使用。

本设备的工作温度可由室温升至最高温度,在此范围内,可根据工作需要任意选定工作温度,选定后靠箱内自动控制系统使温度恒定在所规定的范围内。

操作步骤

接通电源后,打开旋钮开关,设置温度。温度设置完成后,自动进行加热。

将塑料颗粒放入下样板进行预热,待塑料颗粒完全熔化后,盖上上板。到达设定温度后,手动加紧上下两个面板。每次到达设定温度两三分钟后,方可加压一次,以此循环三次。最后等稳定后,拿出样板,用夹子将样板扔入水中冷却。

试品制备完毕,关闭旋钮开关,同时拉下空气开关。

使用注意事项

该箱安装在室内干燥及水平处。

应在供电线路中安装空气开关一只,供此箱专用,并使箱体可靠接地。

安装地线。(此操作由客户自行安装)

本设备为非防爆,对带有挥发性、腐蚀性物品切勿放入,以免发生损坏、爆炸。

当做高压料实验样板时,应在上下样板中加入聚脂薄膜,防止颗粒粘在上下样板上。

样品托板内有凹槽,把样品放入槽内,高于槽一点。

不可任意卸下侧门,扰乱或改变线路,发生故障可打开侧门请电工按线路逐一检查,如遇重大故障与本厂直接联系。

本设备应经常保持清洁,停用时应注意防潮。

易损件

加热管

电流表

聚酯薄膜

Downloads

Original Chinese documents include specifications, configuration and operating requirements.

Selection & support

What information is needed to select a model?

Tell us about your samples, the test method, the measuring range and the configuration you need. Our engineers will confirm a suitable model.

Do all models have the same specifications?

Models and configurations can differ in range, control method and test space. Switch between the models above to see each one.

How do I get a quotation and delivery details?

Send the enquiry form below or call our sales line. Price, delivery time and exact configuration are confirmed by our sales staff according to your needs.

Discuss your testing requirements

Heated specimen press

Tell us about your sample and test method to confirm the model, quotation and delivery.

+86 152 3147 6158
948064885@qq.com

Your enquiry is saved to the Wansu service desk. If the service cannot be reached, an email draft is prepared instead.

Heated specimen press